Cheektowaga is an Erie County town of about eighty-eight thousand residents on Buffalo’s eastern edge, home to the Buffalo Niagara International Airport. Its Building Department issues permits for the unincorporated town, distinct from the incorporated Village of Sloan.
This guide covers the Building Department, the Village of Sloan distinction, the licensing position, and the codes in force.
This guide covers the Town of Cheektowaga. The incorporated Village of Sloan inside the town is a separate authority with its own building department.
The Village of Sloan files separately, and upstate Erie County towns generally do not require a local contractor licence. Unlike the downstate counties, Cheektowaga generally has no county or town general-contractor licence, though workers’ compensation and disability coverage are required. Airport-adjacent parcels can carry height and airspace review.
What requires a building permit in Cheektowaga?
New York builds on a single statewide code — the Uniform Fire Prevention and Building Code, known as the Uniform Code — maintained by the State Fire Prevention and Building Code Council and overseen by the Department of State Division of Building Standards and Codes. The 2025 edition took effect on December 31, 2025, built on the 2024 International Code Council model codes with New York-specific provisions. It applies in every part of the state except New York City, which retains its own construction codes. Executive Law section 379 lets a city, town, village or Nassau County adopt standards higher or more restrictive than the Uniform Code. So the first question in Cheektowaga is which authority has jurisdiction — and in New York that is usually a town or village rather than a county.
Permit required
- New commercial, multi-family and residential construction, additions and change of occupancy
- Structural alterations, load-bearing changes, foundations, decks and retaining walls
- Electrical work — services, panels, circuits, solar and EV charging — under the Uniform Code and the referenced National Electrical Code
- Plumbing under the Plumbing Code of New York State, tied to a locally licensed trade where the jurisdiction requires one
- Mechanical and HVAC change-outs, and work affecting the Energy Code envelope
- Re-roofing above the exempt scope, pools, signs, and demolition
Often exempt
- Minor repairs and maintenance replacing materials in kind
- Small accessory structures below the local threshold, where zoning allows
- Painting, flooring, cabinetry and other finish work
- Like-for-like fixture or appliance swaps with no alteration to wiring or piping
Local amendments and thresholds differ from one jurisdiction to the next, so an exempt list from a neighbouring city is not reliable — a project waved through in one place needs a full permit set in the next. An exemption from a building permit is never an exemption from zoning, the statewide energy or green-building codes, or an electrical or plumbing permit. Confirm scope with the Building Department before work starts.
The statewide layers that apply everywhere
Several layers apply on top of the base building code and routinely catch projects owners assume are exempt: the 2025 Energy Conservation Construction Code of New York State, which took effect alongside the Uniform Code and makes New York the first state to require most new buildings to be all-electric; the truss-construction identification requirements carried in Executive Law; and, in shoreline and flood-prone areas, floodplain administration under the local flood damage prevention law. Snow and ice loading is a live structural constraint across most of the state. Locally, the Town of Cheektowaga enforces the Uniform Code through its Building Department, with amendments adopted by local law.
Who handles permitting in Cheektowaga?
The Building Department issues permits and inspects residential and commercial work in the unincorporated Town of Cheektowaga, outside the Village of Sloan.
| Detail | Information |
|---|---|
| Authority | Town of Cheektowaga Building Department |
| Serves | Unincorporated Town of Cheektowaga, outside Sloan |
| Phone | 716-686-3470 |
| Counter | Cheektowaga Town Hall complex; Mon-Fri |
| Code | 2025 Uniform Code with local amendments |
| Filing | Counter and department submittal |
| Licensing | No local GC licence; worker coverage required |
| Records | Permit records held by the department |
There is no statewide contractor licence, and upstate Erie County towns generally do not require a local general-contractor licence; the department confirms workers’ compensation and disability coverage and any trade registrations. Plumbing and electrical work files under the licensed trades the town recognises.
Parcels near the airport can carry height and airspace considerations reviewed alongside the building permit.
Permit types
Residential permits
Residential work in the unincorporated town is permitted and inspected under the Uniform Code and the town’s local law across its dense suburban stock. Minor in-kind repairs and finish work are generally exempt from a building permit but not from zoning.
How New York contractor credentials work
New York does not license general contractors at state level. There is no state contractor licence, no state exam and no state board for general contracting. Licensing is a city and county matter, and the requirements change as you cross a municipal line. The state regulates home improvement contract terms through General Business Law Article 36-A rather than licensure, so a written contract obligation can apply even where no licence does.
In New York the licence lives with the locality, not the state. A registration issued by one county does not authorise work in the next, and a contractor working across the metropolitan region routinely holds several at once. Confirm which licence the permitting authority requires for the specific parcel before filing, along with workers’ compensation and disability benefits coverage.
Commercial permits
Commercial work goes through department plan review against the Uniform Code, the Energy Code and the fire code, with stamped drawings. Retail, logistics and airport-adjacent commercial work carries site, drainage and, near the runways, airspace review.
Licenses, trade classifications and design professionals
Practically, three credential layers appear on New York projects: the local home improvement or contractor registration where the jurisdiction issues one; separately licensed electrical and plumbing trades, licensed locally rather than statewide; and, on commercial and larger residential work, drawings stamped by a New York-licensed architect or professional engineer. Confirm what the Building Department requires for the specific building before filing.
Cheektowaga permit costs and fees
Budget the town building permit and plan-review fees, separate electrical, plumbing and mechanical permits, and any site or drainage fees. Worker coverage is confirmed with the permit rather than charged as a fee.
| Fee component | How it works |
|---|---|
| Building permit | Based on project valuation or square footage; set by the local schedule |
| Plan check | A percentage of the permit fee or a flat charge, at submittal |
| Trade permits | Separate electrical, plumbing and mechanical fees |
| State surcharges | Building Standards and seismic (SMIP) fees collected with the permit |
| Impact and school fees | Development impact and school-district fees in growth areas |
| Re-inspections and revisions | Additional fees for failed inspections, revisions and expired permits |
New York does not layer a uniform statewide permit surcharge on local charges the way some states do, so the fee is substantially local: each city, town and village sets its own schedule by local law, and neighbouring municipalities on the same road can price the same job differently. A figure from a neighbouring town is not reliable — ask the Building Department for the schedule in force on your filing date.
Need a real number for a specific Cheektowaga project? Send us the scope, address and valuation and we will identify the authority having jurisdiction, the code edition in force and the fee categories that will apply.
Trade permits and who may pull them
Trade permits are separate from the building permit and, on projects that require one, generally cannot be issued until the building permit is in place. Each trade follows its own book within the Uniform Code, and is tied to a contractor holding whatever trade licence the local jurisdiction issues — which is not portable across municipal lines.
New York runs the trades on local licences. Electrical and plumbing credentials are issued by cities and counties rather than the state, so a master licence recognised in one jurisdiction may carry no weight in the next and the permit may have to be pulled by a differently licensed trade. Confirm both the permit and the licence with the authority that issues it.
- Electrical work follows the Uniform Code and the referenced National Electrical Code, under a locally licensed electrician.
- Plumbing work follows the Plumbing Code of New York State, under a locally licensed plumber.
- Mechanical work follows the Mechanical and Energy codes of New York State.
Permit required
- Service installations, panel upgrades, new circuits, solar PV and EV chargers
- New plumbing, repipes, water heater change-outs, fixtures, backflow and gas piping
- HVAC installation and change-out, ductwork, venting and commercial kitchen exhaust
- Sprinkler, standpipe and fire alarm work on commercial and multi-family structures
Typically exempt
- Replacing a fixture, switch, receptacle or light with no alteration to wiring or piping
- Clearing a stoppage without replacing or rearranging concealed piping
- Filter, thermostat and routine component service
- Like-for-like appliance repair that does not alter the connection
How to apply for a Cheektowaga building permit
A parcel inside the Village of Sloan files with the village.
Workers’ compensation and disability coverage are required.
Parcels near the runways can carry height and airspace review.
Commercial and larger residential work needs an architect or engineer seal.
Drawings, trade permits and site submissions as they apply.
The department inspects and issues the certificate of occupancy.
Review, corrections and what actually causes delay
In New York, the first cause of delay is uncertainty over jurisdiction — filing with a town when an incorporated village inside it holds the authority, or assuming a county issues permits when it generally does not. After that come Energy Code documentation, a contractor registration that the jurisdiction does not recognise, and, in shoreline and flood-prone areas, floodplain requirements that were not addressed up front. Build the plan-review time into the schedule and confirm the checklist with the Building Department before filing.
Approvals do not stay live indefinitely. A New York building permit carries a validity period and can expire if work does not start or stalls between inspections. On phased or financed work, keep the permit active with periodic progress inspections and confirm the expiry window before it passes.
Inspections in Cheektowaga
Where a permit is required, standard checkpoints include footing and foundation, framing, rough-in electrical, plumbing and mechanical, insulation and Energy Code compliance, fire systems on commercial work, and final, with a certificate of occupancy before use. The department inspects to the approved plans, with a certificate of occupancy before use.
New York inspections are keyed to the code edition in force when the permit issued, so the approved plans and the Energy Code documentation need to be on site for the inspector to check against. Local code enforcement officials are certified by the state, and the municipality reports its enforcement activity to the Department of State. Confirm the notice the Building Department needs and schedule around its inspection windows.
Do not cover work before the required inspection has been approved. Keep the issued permit, the approved plans, product listings, Energy Code documentation and your correction responses available on site.
Cheektowaga permit search and official resources
Permit records in New York sit with the local authority that issued them. Where the Town of Cheektowaga Building Department is the authority for the Town of Cheektowaga outside the Village of Sloan, it holds the building permit, the inspection history and the certificate of occupancy or compliance. If you are buying, refinancing or renovating, confirm that past work was permitted rather than assuming it was — open permits and missing certificates are a common closing problem in this state.
Confirm the authority having jurisdiction first. New York enforces one statewide Uniform Code outside New York City, but towns, villages and cities each administer it with their own local law, fee schedule and staffing, so the requirements that apply vary by parcel — and a village inside a town is its own authority. Confirm current requirements, fees and review turnaround for your filing date.
These are the primary sources behind this guide. Codes, fee schedules and procedures change — confirm the position for your filing date.
- Town of Cheektowaga Building Department
- NYS Uniform Fire Prevention and Building Code
- NYS State Fire Prevention and Building Code Council
- NYS Division of Building Standards and Codes
- New York State Homes and Community Renewal
Frequently asked questions
Who issues building permits in the Town of Cheektowaga?
The Town of Cheektowaga Building Department, for the unincorporated town. The incorporated Village of Sloan runs its own building department.
Do I need a contractor licence here?
New York has no statewide contractor licence, and upstate Erie County towns generally do not require a local general-contractor licence. Workers’ compensation and disability coverage are still required.
Is the Village of Sloan separate?
Yes. The Village of Sloan is a separate incorporated authority with its own building department. A parcel inside the village files with the village, not the town.
What about the airport?
Parcels near the Buffalo Niagara International Airport can carry height and airspace considerations that the department reviews alongside the building permit.
Do I need stamped drawings?
Commercial work and larger residential work require drawings stamped by a New York-licensed architect or professional engineer.
Which code edition applies?
The 2025 Uniform Code, administered by the town with local amendments adopted by local law.
Simplify Cheektowaga permitting with Alliance Permitting
Cheektowaga rewards confirming the Village of Sloan distinction and the worker-coverage requirements rather than a licence that does not exist here.
Trusted by leading builders, developers, and national contractors — 22 years of filing in the jurisdictions we write about.
Contractors and builders choose Alliance for Cheektowaga because the work is done by people who have stood at the counter:
- We confirm the Village of Sloan distinction before filing.
- We confirm the worker-coverage requirements the department needs.
- We check airport-adjacent height and airspace conditions.
- We assemble the stamped plan set for commercial and larger work.
- We coordinate the electrical, plumbing and mechanical filings.
Alliance Permitting is a permit documentation and submission company. We prepare your paperwork, file it correctly and coordinate with the permitting authority through issuance. We are not a contractor and we do not perform licensed plan review or inspections; that work stays with your licensed team and the jurisdiction.
Ready to break ground in Cheektowaga sooner?
Let Alliance prepare, file, and track your Cheektowaga permits while your crew stays on the job.
More New York permitting guides
This guide is provided by Alliance Permitting for general information about Cheektowaga permitting. Requirements, fees, and procedures change; confirm details with the permitting authority before relying on them.